PN 6800-30-50485 Patient Monitor Module Mindray IBP Module

Patient Monitor Module Mindray IBP Module PN 6800-30-50485 for Mindray T Series Patient Monitor

Mindray IBP Module PN 6800-30-50485

► Brief Introduction

The Mindray IBP Module PN 6800-30-50485 is a medical device used for measuring invasive blood pressure. It is compatible with Mindray patient monitors and is attached to the patient through a catheter placed in an artery.

The device works by converting the pressure exerted by the blood in the artery into an electrical signal, which is then transmitted to the patient monitor. The monitor then displays the blood pressure measurements in real-time, allowing medical professionals to monitor the patient's condition accurately.

To use the Mindray IBP Module PN 6800-30-50485, the catheter is first inserted into the patient's artery. The module is then attached to the patient monitor and connected to the catheter. The blood pressure readings can be monitored and recorded over a prolonged period, helping medical professionals track the patient's condition.

Overall, the Mindray IBP Module PN 6800-30-50485 is a critical tool for monitoring patients with invasive blood pressure measurements and improving patient outcomes.

► IBP Tests

IBP Performance Test

1. Connect the patient simulator with the pressure module.
2. Make the patient simulator outputs 0 to each IBP channel.
3. Press the Zero Key on the module to make a zero calibration.
4. Configure the patient simulator as P (static) = 200 mmHg.
5. The displayed value should be within 200 ± 2 mmHg.
6. If the value is outside of these tolerances, calibrate the pressure module. If the IBP module was calibrated with a dedicated reusable IBP sensor, check the calibration together with this IBP sensor.
7. Make that the patient simulator outputs 120/80 mmHg ART signals and 120/0 mmHg LV signals respectively to each IBP channel and check that the IBP wave is displayed correctly.
8. Repeat the steps above for all the IBP channels.

IBP Pressure Calibration

1. Connect the patient simulator to the pressure connector on the module.
2. Set the patient simulator to 0 pressure for the desired IBP channel.
3. Press the Zero Key on the module to make a zero calibration.
4. Configure the patient simulator as P (static) = 200 mmHg.
5. Select [Main Menu]→ [Maintenance >>]→[User Maintenance >>] →[Cal. IBP Press. >>]. In the [Cal. IBP Press.] menu, set the calibration value to 200 mmHg.
6. Select the [Calibrate] button next to the desired IBP channel to start a calibration.
7. If the calibration is completed successfully, the message [Calibration Completed!] will be displayed. Otherwise, a corresponding message will be displayed.

To perform a calibration:

1. Connect the 3-way stopcock, the sphygmomanometer and the balloon pump through a T-shape connector, as shown below.

2. Zero the transducer. Then open the stopcock to the sphygmomanometer.

3. Press the Main menu button on the equipment’s front panel. Select [Maintenance>>]→[User Maintenance >>]→ enter the required password→[Cal. IBP Press. >>]. Then configure IBP calibration value.

4. Inflate using the balloon pump until the reading of sphygmomanometer approximates the preset calibration value.

5. Adjust the calibration value in the [Cal. IBP Press.] menu until it is equal to the reading of sphygmomanometer

6. Select the [Calibrate] button to start a calibration

7. The message [Calibration Completed!] is displayed after a successful calibration. If the calibration failed, the prompt [Calibration Failed!] will be displayed.

►Quick Details

Thank you for your time! If you have other questions about our Mindray IBP Module PN 6800-30-50485, please feel free to contact us. We are always ready to serve you.

6800-30-50485 Patient Monitor Module

Mindray IBP Patient Monitor Module

PN 6800-30-50485 Patient Monitor Module Mindray IBP Module Images